throatdash7

Reasons to Change Door Lock There are many reasons to replace your the lock on your door, from increasing your home's security to redecorating your entrance. You may need to change locks if your key gets stuck or becomes difficult to turn. DIY novices can easily alter their locks. To begin, gather the materials you need. Remove the old lock Before installing a new lock it is essential to remove the old one from the door. This is important in the event that you suspect that someone else has a key to the house. It is also an excellent idea if have recently moved into a home that was burglarized, or welcomed a new roommate. It's simpler than you think and can be completed in a matter of minutes. Begin by removing the screws that secure the deadbolt faceplate on the frame of the door. You'll need to take off the screws on both sides of the door to remove the faceplate. This will allow you to see the inside of the door and provide you with a better understanding of how to continue with the remaining steps. After removing the old faceplate, you will have to remove the bolt along with the strike plate and strike plate. Remove the bolt from the door hole using a screwdriver. If the bolt is rusted, you may have to use a chisel or smash it. If you are using a chisel be cautious not to scratch the door frame. Before you take out the lock that was previously in use, make sure that your new deadbolt and doorknob will fit into the existing holes in the door. Most hardware stores and big box stores sell several different types of locks and can help you find the right one to meet your needs. Ask for help if the lock you purchased doesn't fit your door. While you are removing the lock that was previously in use, look for small notches or depressions in the handle or around the trim. If Repair My Windows And Doors can find them, slide a straightened safety pin or a flat screwdriver into them to loosen the handle and expose screws underneath. After the screw in the handle is removed, you can now begin to remove the knob from its spindle. To do this, locate the set screw located at the base of knob and loosen it. Then, take the spindle off. Install the new lock It's a good idea change the locks on the doors of your home periodically, especially in the event of a burglary or you move in with roommates. It is easy, cheap and effective to change the lock on your door. Most people can do this yourself with a screwdriver and some basic instructions. You may also wish to know how to rekey your door lock to ensure that only you have the key. To start the process, you'll must purchase a new lock that matches your existing lock's keyway. Locksmiths are usually able to rekey your lock for you for a fee however, you can save money by doing it yourself. You can purchase a brand new lock at an hardware store, or on the internet. A standard deadbolt should be able to fit on doors of all sizes, but you'll need to measure the area on your door to ensure that it's a good fit. The lock you buy will typically come with a diagram that will show how to install it on the door. The template can be used to drill the hole. It's much simpler than having to measure every time. If the template doesn't align with your hole, you can take it back to the shop and get another one. The new lock on the right side of the door. Examine the latch. It should have a label that reads “up” or similar. Make sure the latch is seated correctly within the latch plate then secure it with the screws provided. If you're replacing locks on doors it is also essential to be aware of the handing. Certain knob locks are left-handed. If you're not careful, you may place the knob on the wrong side of the door, which could prevent you from locking it from either the inside or the outside. When you're done, you should test the new lock to confirm that it functions. You should be able to lock and unlock the door with a key from the inside as well as the outside. If you aren't satisfied with the result you can always contact a professional locksmith to fix the issue. Test the lock A door lock that will not open can be a hassle, but it can also put your family's safety at risk. It's easy to fix the majority of problems with door locks by conducting some troubleshooting and lubrication. Make sure that the key is properly cut, and that the lock assembly isn't dirty or loose. If this doesn't solve the problem, you can try applying lubrication to the door lock actuator using powdered graphite or a silicone-based lubricant. Make sure that the door lock switch, wiring harnesses and the actuator connector are all working correctly. To check this, refer to the manual or wiring diagram to determine the purpose and color-coding for all the door lock switch wires. Utilize a digital meter or test light to check if the actuator is receiving power and ground when the switches are activated. If you see voltage switches that toggle with each other it means that the switches are in good shape and the actuator is likely to need replacing. If the switch appears to work but the actuator doesn't move when you turn it, there may be a problem in the cylinder. The actuator cylinder is outfitted with pins that are spring-loaded. They prevent the cylinder from rotating until the key is put in, which then pushes them upwards to meet the height of the key at the location. The cylinder then begins to rotate, opening the lock body and opening the latch to open for the handle. If the door lock actuator is still not working, you can take it off it by using a small screwdriver. You will need to remove the locking bolt first and then remove the plastic cover that holds the electrical connector. After that, disconnect the door lock actuator, and let it fall. Then you should be able to locate and remove the two 10mm bolts that hold the actuator in position. Once the actuator is removed, you should be capable of disconnecting the black electrical connector and remove it together with the actuator and lock assembly. Replace the key If you have an unkeyed deadbolt or door knob, if it is not working properly you need to either change the lock's key or rekey it or replace it completely. It is not difficult to do it yourself and can save some money. However, before you do this it is an excellent idea to get a locksmith to examine the locks and check for any issues. This will give you peace of mind knowing that your home is safe and secure. Remove the exterior faceplate of the doorknob/deadbolt. There may be screws that are holding it in place, you need to remove them, use a screwdriver to loosen them and pull the faceplate off. Then, remove the interior faceplate using a flat-head screwdriver. After removing the faceplate, you can remove the bolt and screw from the lock cylinder. A locksmith can help determine if your lock requires replacement or rekeyed. They can also advise you on the best security solutions for your home. They can also make the necessary adjustments to your door and frame to ensure an ideal fit. They also provide a warranty on their work. If you decide to rekey the lock you'll have to first buy an additional key for it. It is important to use a lock key that fits snugly. A key that is not properly fitted could cause damage to the mechanism inside and stop it from working. Insert the key into the lock to test its size. If the key is flush against the plug, then it's the right size. If the pins stick up from the top of the plug and are not a good fit, they're too long. You may want to replace your door lock for a variety of reasons, including: If you're moving into an owner's residence or lose your keys, rekeying the lock is an affordable option than replacing it. It can also be more cost-effective than a complete replacement. Rekeying an existing lock may not be possible in certain situations. For example, if the lock is damaged or repeatedly blocked, it's time to replace it.